community natural gas steam boiler manufacturers

2tph WNS series gas-fired community steam boiler manufacturers project for feed industryTempering is a crucial link in the granulation process of feed industry; the performance of tempering has a direct impact on the quality of pellet feed. Currently, feed mills use steam to complete the tempering process; hence, a steam boiler is a core equipment for feed industry. Nanjing Shuaifeng Feed Co., Ltd. is established in 2005, its major products consist of aquatic feed, tubificidae, fish feed and crab feed. To improve the feed quality and response to global environmental policy, Nanjing Shuaifeng Feed Co., Ltd. planned to reintroduce an efficient and environment-friendly steam boiler. After a series of contrastive analysis on a lot of boiler products, the company was attracted by the high performance of ZOZEN WNS series gas-fired (oil-fired) boilers, and order one set of 2tph steam boiler. This kind of boiler has wide fuel adaptability, including natural gas, light diesel oil and much other clean energy; with low NOx burner, ultra-low emissions of nitrogen oxides can be easily achieved. Meanwhile, the boiler adopts a large-diameter corrugated furnace to ensure the full combustion of fuels; the sufficient storage areas of steam and  heating surface can effectively improve the thermal efficiency of the boiler as well as the the quality of outlet steam.

The reason you need to know the boiler energy consumption (reheat steam temperature) reheat steam temperature problems 1. Circumstances reheat temperature rises 1.1 Move boiler furnace flame center, furnace outlet temperature increases (see main economic indicators No. 5 boiler exhaust gas temperature). 1.2 coal increased too fast. 1.3 Excess air amount is increased. 1.4 pulverizing system start-stop. 1.5 Automatic control of the reheater desuperheating water improper adjustment. 1.6 reheater sootblowing time poor choice. 1.7 feed water temperature is low. 1.8 the high pressure turbine exhaust temperature is high. Next to the 1.9 high leakage, high reheater inlet temperature. Hot and cold extraction section greater then 1.10. 1.11 boiler heating surface design is unreasonable, over-temperature reheater tube wall, forced cooling operation. 2. Reheat the following partial flame temperature is lowered center 2.1: burner tilt deviation, hem; burner is switched from the upper to the lower layer, the lower layer or to an excessive amount of the powder; volatile coal fraction is increased, the pulverized coal thinning, water reduction. 2.2 reheater heating surface fouling, slagging, fouling the interior. 2.3 Save reheat the heated drain valve. 2.4 automatic adjustment inappropriate, excessive reheater desuperheating water. 2.5 feedwater temperature. 2.6 economizer and water wall sootblowing time poor choice. 2.7 reduce the amount of coal too fast. 2.8 # 1, # 2 high pressure heater is disabled, increasing the reheated steam flow.

Steam boiler configuration and price performance advantage of fast boiler community steam boiler manufacturers is a new technology based on conventional steam boilers, improved from the depth of research and development, superior work performance is more stable and energy-saving, comprehensive ability to work the next level, in recent years, is also a very popular steam boilers, steam it can meet the operational needs of most users, popular with users. The new integrated operation of the new steam boiler steam boiler performance is relatively stable, at work, saving and environmental protection, as well as the amount of steam long run all have good performance. Low energy consumption, low cost using 220V household electrical lighting, the total electric power does not exceed 1.5KW, about 3 minutes at room temperature the water vapor, efficient energy saving. For a wide range of new steam boiler Application: Washing Ironing industry, food processing industry, packaging machinery industry, bio-chemical industry, and so the high degree of automation with full touch screen smart intelligent control, a key to start without special guards, overpressure display, water display, temperature display, the display timing of other functions. Efficient use of energy saving integral mounting machine, factory installation is completed, Built Preheater, first use is not completely absorbed by the flue gas waste heat to heat water at room temperature, having a low exhaust gas temperature in line with the national emission standards. If new and existing steam boiler steam boiler operating parameters do not meet your production conditions, you can also choose to communicate with manufacturers to discuss, select tailor-made, custom manufacturing model is suitable for your needs. Fast boiler heat equipment has accumulated years of production experience, thousands of users to solve production problems, free of charge for many users tailored production program, subject to a number of users, more relevant information if you want to get quote or to learn more, you can call us or click on the online consultation, free 24-hour staff will answer your questions!

Further reading: Xuedong, male, Han nationality, born in August 1964, Tongling, Anhui Province, Communist Party members. Chinese Academy of Engineering, Director of the National Pressure Vessel and Pipeline Safety Engineering Research Center. He is the authority in the field of pressure vessels and piping of heat transfer, it specializes in high-temperature, high-pressure manufacturing issues at the state of the pressure vessel, and the Group's development has a strong bonding point. August 1986, Chemical Engineering and Equipment, Zhejiang University graduate. February 1993 - December 1995, a master's degree in chemical engineering Zhejiang University to study mechanical engineering. February 2001 - June 2004, in chemical engineering machinery Zhejiang University PhD. In November 2006, Ho Leung Ho Lee Foundation Science and Technology Innovation Award. June 19, 2017, in Anhui Province, Anhui Province Party Conference elected as delegates to attend the nineteen Party.