2 ton gas fired steam boiler in pakistan

Wuhan Port District Social Welfare Institute (apartments for the elderly) is invested by the government pension services, with a total construction area of ​​38,000 square meters, 532 beds, mainly adopt destitute persons, social support on behalf of the elderly. Hope to provide welfare to the elderly year-round 24-hour hot water, the original boiler equipment can not meet this demand, therefore, require additional purchase orphanage hot water boiler. After much investigation, in cooperation with the welfare determined fast boiler, provides three integrally condensing gas hot water boiler (WNS1.4-1.0 / 95/70-Y.Q) by a fast boiler.

Spark ignition rods gas boiler, but because the misfiring spark ignition rods gas boiler misfiring but the reasons: 1, the cyclone disc space ventilation is blocked carbon, poor ventilation. 2, dirty oil nozzle clogging or wear. 3, the throttle angle is set too small. 4, the firing bar from the leading edge from the oil nozzle tip inappropriate (too protruding or retracted) 5, the first solenoid valve is an oil debris blocking gun (gun small kerosene). 6, oily or too viscous to flow easily clogged or the oil filtration system the valve is not opened, so that insufficient suction pump, oil pressure. 7, the filter pump itself blocked. 8, the oil more water (boiling abnormal noise within the heater). Gas boiler ignition spark rod action but misfiring are: clear; the first washing, such as not renewed; turndown test; adjusting the distance (in 3 ~ 4mm as well); Remove cleaning (cleaning the parts diesel) ; For more information about oil oil oil, information technology please pay attention to the public number of oil rings. Check the pipeline and oil filters, insulation equipment; peripheral screw pump removed, carefully remove the cover inside out net oil, diesel oil immersion; renewal of the test oil. When the gas boiler and turn the fire a small fire normal, off, or flashing the causes of instability: 1, air volume damper setting fire too. 2, oil fires micro switch valve (damper outermost that group) inappropriate setting (set throttle air flow rate is greater than the fire). 3, oleaginous easy to spray viscosity is too high (heavy). 4, and the nozzle plate spacing cyclone inappropriate. 5, fire nozzle worn or dirty. 6, the preliminary fuel tank temperature is too high, so that the steam not smooth oil pump oil feed. 7, gas hot water boiler fuel oil water. When a small fire gas boiler normal and turn the fire extinguished or flashing instability action: Test gradually reduced; heating temperature; adjusting the distance (between 0 ~ 10mm); clean or replace; i.e., set to about 50 deg.] C may be; or drain oil change.

The inlet speed of gas-fired hot-water boiler before start-up should not be too fast, usually no less than 4 hours in winter, and 2-3 hours in other seasons, especially in the initial stage of water intake. The inlet temperature of a gas-fired hot water boiler is generally 50 °C, so the difference between the feed water temperature and the steam wall temperature in the drum is less than 40 °C. For gas-fired hot water boiler, the inlet water temperature can be equal to that of steam drum wall without complete cooling, otherwise the inlet water speed should be slowed down. When feed water enters the drum, it always first touches the lower part of the drum. If the difference between the feed water temperature and the drum wall temperature is too Large, the inlet speed is fast, and the upper and lower walls of the drum, the inner and outer walls will have a large expansion. Bad, on the drum caused a lot of additional stress, resulting in drum deformation, serious cracking. Due to the thickness and slow expansion of the drum wall, the tube wall connected to the drum wall is thinner and expands faster. If the inlet temperature of the gas-fired hot water boiler is too high or the inlet speed is too fast, the expansion will be uneven, the welded joint will appear cracks and the gas-fired hot water boiler will be damaged. The inner diameter of the decompression tube is usually φ 7~13mm (water and steam), and its length should not be too long (< 60m). Straightness of pressure pipe If the diameter is too small and the length is too long, it will affect the dynamic transmission of pressure measurement and increase the dynamic error. The inner diameter is too large to be easily maintained and installed. Pressure pipes should not be placed in the horizontal part to prevent the accumulation of bubbles (when measuring liquids) and water columns (when measuring gases). The pressure tap shall be perpendicular to the flow of the medium. Pressure faucet must not have chamfer, flange and burr. When measuring the hydraulic pressure of an electrically heated 2 ton fired steam boiler in pakistan, the pressure outlet should be removed from the lower part of the pipe to prevent the gas in the liquid from entering the pressure guide pipe; When measuring the gas pressure, remove the pressure splice from the upper part of the pipe to prevent dust and dust in the gas The droplets enter the ignition line. The installation site of the electric heating steam boiler pressure gauge (pressure transmitter) should meet the environmental conditions (temperature, humidity, vibration, etc.) used by the instrument, and should be easy to observe, repair and ensure safety. Insulation should be laid on pressure pipes in high temperature media to avoid burning during flushing. Pressure lines are equipped with needle valves (for cutting off pressure in the event of pressure line failures during operation), auxiliary needle valves (for use with instruments, stopping, replacement), condensing coils and elbows (isolation elastic elements from high-temperature media), Easy to install sealing gaskets) as well as sewage valves and sewers. For special pressure measurements, it's still pressing. Install discharge valve, isolation room and so on in the force pipe.

Gas steam thermal cracking reaction furnace gas steam oven should be carefully introduced reflect in the use, to guard against water, acid, alkali and leakage into the low boilers using the system, the system should be installed filters installed to prevent debris into various types, to ensure the purity of the oil . Gas and steam is easily oxidized during heating, the acid value of the oil is increased at high temperatures and a large change rate. Steam oven gas kinematic viscosity gradually increases, which is due to the thermal cracking gas vapor component at high temperature, thermal polycondensation reaction. Thermal cracking reaction resulting in generation of small molecule compounds, to reduce its viscosity; oxidation temperature when the inner conduit thermally cleavage occurs at 300 ~ 400 ℃, coke formation in the pipe, the inner wall of the device, leading to heat accumulation pipe affect the heat transfer efficiency, sludge poor flowability, transfer oil accelerated aging failure, but also to the furnace, pipes local overheating, impairing the mechanical strength of the threat to personal safety.