Cheap 2t Natural Gas fired steam boiler Cyprus

The main components of the boiler: boiler lot of people know, but do not always understand the boiler, even customers who have purchased the boiler is not very understanding of what are the component parts of the boiler. Today to look at a detailed analysis of boiler components which mainly consists of: 1, drum. Its role is to collection, storage, and supplementary steam feedwater purification. In water-tube boilers usually 1 to drum 2, the drum is called a steam drum (drum), referred to below water or mud drum drum. The inner drum has a uniform distribution of the feedwater tank, and the water separation means the continuous blowdown apparatus. Internal boiler drum water tube assembly and a separator and the like. The outer drum containing the main steam valve, the sub-steam valve, safety valve, air valve, water level gauge, sewage connection pipe and pressure gauges. One end of the head or top of the drum was Manhole. One end of the drum head with the open manhole bottom with periodic discharge means. In many riser and downcomer (bundle) connected to form the entire structure of the elastic member between the upper and lower drum. 2, water wall heating surface. It is disposed around the furnace radiation heating surface. Boiler tube made of φ51 × 3 ~ φ63.5 × 3.5mm in industrial boilers generally used rust, while the main heating surface of the water tube boiler. Radiation heating surface absorption of radiant heat and flame shield the furnace wall, and thus play a protective role in the furnace wall; the same time, as more endothermic, the furnace temperature can be reduced, as well as to prevent burning effect coking coal seam. 3, header. It is a collection of tubes arranged in the main element is coupled, and a dispensing action of water drawn, its location has upper header and a lower header or inlet header and the outlet header bin of. A header welded seamless steel pipe is generally greater diameter and two end caps. In recent years, some manufacturers shut spinning tube ends, substituted welded end cap, a more rational structure. 4, the convection heating surface tubes. Convection convection bank known as the drain pipe, located between the upper and lower drum, generally by a boiler φ51 × 3mm steel composition, the main heating surface of the water tube boiler. In order to sufficiently absorb heat, convection bank usually intermediate, separator trap wall consisting of a flue or turns back and forth, increasing the flow of flue gas, and smoke at high speed across tube bundles. 5, the pyrotechnic heating surface tubes. Smoke tube heating surface is the main fire tube smoke-tube boiler and a combination boilers, its role is as high temperature flue gas generated from the combustion furnace flows through the inner tube, the outer pot of water continuously on the heating tube, it gradually becomes steam (or hot water). Smoke tube is typically mounted pot shell, fixed to both ends connected to the tube plate by welding or expansion. Because of its limited number of installations of the boiler shell, plus content of the tube is easy to plug fouling, easy outer tube fouling, it is not practical for large boilers. 6, the superheater. Economizer and air preheater, which belong convection heating surface. Superheater convection superheater addition, there are radiation superheater, economizer and a preheater rest are mounted boiler backpass. Their role in the main exhaust gas temperature is further reduced, improving the thermal efficiency of the boiler.

First, when the flue temperature dropped to below 50 ℃ Solution: Check the tail may enter the flue if heated, while the flue thoroughly remove soot. No burning flue tail, can be re-started ignition; if burning, should be replaced, repaired burning member. Second, the combustion chamber when the negative pressure is too large Solution: When the exhaust gas temperature close to the temperature of the injected steam, or less than 150 deg.] C over 1 hour and stable, open the inspection hole inspection; after inspection after confirming the fire source, before start the fan ventilation. Third, shutdown or fire, air gun valve ajar solutions: reinforcing and electric cheap 2t fired steam boiler cyprus feed water drainage, or open the valve economizer recirculation tube to protect the economizer is not burning. Fourth, Kai, during shutdown lower furnace temperature, a solution of unburned fuel in the furnace: extinguishing device immediately put into vapor, carbon dioxide or other devices off fire. Five burning improperly adjusted, with insufficient wind or with the wind unreasonable Solution: Close the flue duct and baffle around the door opening, start sending prohibited, induced draft fan. These are the methods of electric heating steam boiler fast boiler to provide you with the handling of soot in the chimney, if you use electric steam boilers, with more than five can control their own boiler equipment need to be cleared up the flue, and select the appropriate method .

This is our first collaboration with fast boiler, professional and caring service fast boiler's impressed us. From pre-sales advice to after-sales guidance, every step is very careful and thoughtful. They provide hot water boiler performance is also very good, and effectively improve the level of our heating units. --customer feedback

Why condensing boiler sales will increase every year? Under the influence of the modern concept of energy saving in the purchase of products like heating is more popular in condensing boilers, statistics confirmed that showed sales rising year by year in the state during the years of research and development come out of condensing boilers. So why year after year of rising sales of a full range of condensing boilers do? We will be analyzing the reasons for the rise in sales of condensing boilers below. One reason, can save heating costs are well known in the modern condensing boiler has not yet come before people in many parts of the device only by means of conventional boiler when heating is influenced by the principle of cause conventional boilers spend a lot of energy to release some heat . But they have very different condensing boilers and conventional boilers in the design and working principle of the above, the use of modern release can save heating costs on top of a relatively large amount of heat condensing boiler to a certain extent. Two reasons, can reduce the frequency of replacement of modern heating equipment currently on the market of raw materials existing ordinary boiler product is mostly copper, after long-term use of corrosion and thus vulnerable to a series of failures to be replaced. Condensing boilers produced material was stainless steel, even if the contact during operation of the steam does not affect their quality will be able to make virtually modern replacement frequency heating apparatus is controlled. Class three reasons, the release of a very small amount of nitrogen oxides during the operation most of the conventional type boiler in operation of heating equipment are required to coal-derived material as a raw material, coal or the like at the time of combustion of the material will release a large ships harm air quality material composition. While condensing boiler during operation of the steam is produced after combustion of natural gas as a raw material, and therefore the operation at the time of release of the content of nitrogen oxides is much lower than a predetermined standard. Analysis of the reasons condensing boiler sales rising year by year made temporarily come to an end. Through the above three reasons we can have some understanding of the advantages of using credible condensing boiler from the side, I believe that with these advantages condensing boiler different from the ordinary boiler heating equipment will continue to grow in future sales.