Energy-saving measures and methods of industrial bath center steam atmospheric pressure fire tube boiler dealers which industrial boiler energy-saving measures and methods which 1, to increase the capacity and improve the thermal efficiency of boilers and inefficient small compared to the large-capacity high-efficiency industrial boilers, can greatly improve the utilization of energy rate, so as to obtain greater economic benefits. Meanwhile, the cogeneration project enables conversion of exhaust or extraction steam turbine for heating, not only can reduce the loss of turbine exhaust steam, but also help to save coal resources. Industrial boiler thermal efficiency of China's low is a fact that can not be ignored, usually operating efficiency even lower. Therefore, improving the efficiency of industrial furnace hot pot, is crucial for energy savings. In one aspect, by improving the quality of the insulating material, thicker insulation, heat loss can be reduced. On the other hand, the use of secondary air system, can facilitate a more complete combustion of fuel, the effect is very significant. 2, the heating surface to reduce coking and fouling of industrial boiler during running, prone to coking, fouling phenomenon, resulting in increased and then decreased local resistance to the flow cross section. Not only conducive to smoke, but also so that heat transfer is reduced, further increasing the temperature of the flue gas. Industrial boilers and cleaning agent has a good cleaning effect, can be put in the appropriate amount sublimation decompose at high temperatures, with the heating surface of the coke, slag and contacts a chemical reaction can be automatically off after decomposition. Meanwhile, a method of periodically purging is also more effective in the early formation of fouling was loose state can be cleared periodically sootblowing. If the attachment is too long time, will translate into close like fouling, thus increasing the difficulty of cleaning up. 3, to ensure the quality of coal and industrial coal-fired boilers with coal is crucial, its moisture, volatile content factor for the speed of fire, as well as affecting the combustion temperature is extremely obvious. Maintain proper moisture content can be reduced with reduced leakage occurrence of coal and fly ash, coal seam and helps enhance the evacuation ventilation. If the moisture content is too high, will affect the speed and the temperature in the furnace, heat loss will be increased exhaust smoke. Industrial water boiler heating surface for scaling impact of large scale for each additional 1mm, the overall thermal efficiency of the boiler will be reduced by 3%. 4, many factors affect the lower exhaust gas temperature industrial boiler flue gas temperature, within the course of the economizer scale, cleaning up soot neglect of smoke in the furnace wall channeling smoke, poor treatment effect, can cause elevated exhaust temperature. On the one hand, to deal with the heating surface appears slagging, fouling and scale phenomena take timely measures to eliminate, minimize or avoid their presence. On the other hand, on the rear of the boiler heating surface is improved or increased. Industrial boiler flue gas temperature, objectively reflects the utilization of exhaust heat. But not as low as possible, the exhaust gas temperature is too low but not conducive to the normal operation of the boiler.

The preparation you need to do before the bath center steam atmospheric pressure fire tube boiler dealer is installed

The boiler is a device that supplies steam and hot water for industrial production or daily life. After the company purchases the boiler model, it needs to consider the installation problem. The installation of the boiler is directly related to the important steps of the smooth operation of the boiler, except for the installation of the auxiliary machine. Also need to pay attention to the preparation before installation.

1. Handling the registration of natural gas boiler installation: According to the “Safety Supervision Regulations for Steam Boilers”, the units that use the boilers should go through the registration procedures one by one. The boiler use unit shall have a person responsible for the boiler installation work, responsible for contacting the local boiler supervision agency and filling out the installation notice. When the boiler is installed, it must be attended by a furnace, and it is equipped with a pipeman, a fitter, a hoist, a cold workman, an electric welder and an auxiliary worker.

2. Determine the installation location and qualification of the boiler to determine the installation location. The boiler installation unit must have a boiler installation qualification certificate issued by the superior authority in accordance with the installation scope.

3. Inspection of boilers and accessories: Before the installation of natural gas boilers, the boiler body, combustion equipment, components, natural gas boiler auxiliary machines and accessories shall be inspected and accepted according to the drawings, and records shall be made. If it is found that the relevant standards are not met, it shall be promptly submitted to the factory. .

Low NOx emission combustion bath center steam atmospheric pressure fire tube boiler dealer technology a boiler combustion boiler hypoxic hypoxia NOX emissions from combustion is the easiest way to control. And a combustion burner system does not need to make any changes, only control air flow into the furnace in operation, pulverized coal combustion process as close to the theoretical combustion air amount. Low oxygen combustion scheme can reduce NOX emissions by 20% to 30%. The program practical application subject to conditions. Low oxygen furnace, will increase the amount of unburned carbon, and more difficult for the flame of burning coal more obvious; Further, the CO concentration is also increased so that smoke, which will cause decreased boiler efficiency. Another problem is that for certain boilers, hypoxia causes the main combustion steam or reheat steam temperature is low. The burning coal to immediately, boiler efficiency and reduce the magnitude of steam temperature and other properties to determine the appropriate control value of flue gas oxygen furnace outlet (at or economizer) the specific embodiments. Second, air staged combustion technique combustion air into a plurality of strands, it is gradually mixed and pulverized coal combustion, so you can see the local area to reduce the air-fuel ratio, and the thermal decomposition of coal in the ignition phase, due to hypoxia, and thus the nitrogen oxide generation is suppressed. Air classification may be implemented within the combustor, the boiler can be completed within. 85% of the amount of air required for complete combustion is introduced to the main burner, the main burner combustion zone is insufficient oxygen for the fuel-rich conditions. Due to insufficient amount of oxygen, the flame temperature is low, the amount of nitrogen oxides to less generation of fuel nitrogen intermediates (e.g., NCH, NH3, etc.) will therefore not be oxidized NOX. Meanwhile, it has been possible to further reducing NOX generated in a reducing atmosphere to molecular nitrogen (N2 of), as a result reduces NOX emissions. An upper portion of the top floor is provided Ge overfire air (of OFA) spout into the furnace through which about 15% of the rest of the air, to avoid the high temperature flame zone, it is also possible to burn unburned carbon particles, to complete the combustion process.

Beijing New Energy Automobile Co., Ltd. is China's first to operate independently and gain new energy automobile production qualification of new energy auto companies, mainly engaged in new energy vehicles and key parts and components research and development, production, sales and service business segments, and the layout intelligent manufacturing, energy management, smart travel, Internet +, and other strategic emerging industries. In the new energy automobile manufacturing process, and a series of paint drying processes can not do without the help of hot water bath center steam atmospheric pressure fire tube boiler dealer. Due to the company before the device has reached less than the growing production needs, the introduction of the 2017 mid-tail electric company producing heating pressure hot water boiler (CEDR0.7--95 / 70-Ⅱ).